Loading...
Home > Error Code > Hydro Spa Error Code Flc

Hydro Spa Error Code Flc

Contents

Thank you, Matt Randy August 18, 2015 at 7:49 am My tub is a Free Flow, I have been having LF low flow issues for some time an tub will not If it does not close the contact you're going to get an FLO. BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. Source

Both are secured with black plastic nut around the gray cable. The first thing and most important thing to try is to restart your Arctic Spa by turning the breaker off and on again. The system returned: (22) Invalid argument The remote host or network may be down. Ask Your Own Pool and Spa Question Share this conversation Related Pool and Spa Questions Question Date Submitted I have a hotsprings hot tub and the breaker keeps tripping 10/16/2016 10/16/2016 http://www.spadepot.com/spa-error-codes.htm

How To Fix Flo Error Hot Tub

I have replaced every part of this hot tub all the way done to the wires and sensors. Check out our article: How to release and airlock in your hot tubWhat causes a hot tub flow error? Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously.

Ask Your Own Pool and Spa Question Customer: replied4 years ago. Before we get into what causes a flow error and how to fix it I should probably explain what a low flow actually is.What is a hot tub flow error?On either Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on. Hydropool Hot Tub Error Codes If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open

We need to understand, right off the bat, a pressure switch has two error codes. Do I need to replace the pump? will do thank you for your time Expert: spaman101 replied4 years ago.

If water level is not the problem you should remove the filter cartridges from the spa.

One is pump one is actually running on low speed and two, that there's movement of water within the hot tub. Marquis Spa Error Codes See below for further explanations: FLO, FLC, FL, FL1, PS, Blinking LightsPressure/Flow Switch Failure:These codes are related to flow issues or the pressure switch/flow switch and are by far the most But if that's all working properly, then the next step is that we want to look at the pressure switch. I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct.

Hot Tub Error Codes

Check the water level. http://www.spatecservice.com/error-codes-digital-or-blinking-indicator-light.html This process will clear the PC board of the error and if the filters were the culprit, your spa should start heating and running normally. How To Fix Flo Error Hot Tub Working... Balboa Hot Tub Error Codes Power on the spa must be cycled before the heater will function again.

In rare cases (usually warmer climates), the circulation pump may also cause overheating.The following is a list of most probable causes of this message. http://renderq.net/error-code/ibm-error-code-192.php I did some more troubleshooting online and found to adjust the pressure switch wheel. Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. I turned the hot ton on and off again and it was the same thing. Vita Spa Error Codes

No LF or dry warnings. So, at this particular time I would know that everything is running and this pressure switch is faulty because it keeps going to FLO. Check for clogged filter.FL2 = Pressure switch problem. http://renderq.net/error-code/ibm-c33-error-code.php I know we just recently replaced the screen cause it went out just don't know why it keeps shutting down, to the point we have to turn off the main power

Thank you! Great Lakes Hot Tub Error Codes Check for debris on the heater element. Phil Dissek June 6, 2016 at 8:54 pm I have a 2010 Marquis Rondevous spa and I just replaced the impeller (after changing the water and filter).

See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end.

See M7 Sensors here. Browse by Price $0 - $24.99 $25 - $49.99 Over $50 CUSTOMER SERVICE Contact Us Shipping Return Policy Privacy Policy Testimonials MY ACCOUNT View Cart Account The most common valve; the tee handle valve (also known as gate or slice valve), will show that the handle is up, but in many cases the gate is still half FINAL NOTE: Most spas are equipped with pressure switches and can be found threaded into the stainless steel heater manifold. Hot Tub Error Code Oh Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog".

If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected. Thanks again. I can jumper and make it work. http://renderq.net/error-code/ie-error-code.php HotTubsByArcticSpas 127,011 views 9:09 How to build a Cedar Wood Hot Tub - Duration: 18:53.

Bob karen June 22, 2012 at 10:41 am Hi I have a soleil vita spa. I went counter clockwise onn the adjustment and thought I had resolved the problem. The first thing that you want to do if you get these error codes, is actually take your breaker and turn it off and then turn it back on. Touch any button to reset the system.

If you are a die hard do it yourself'er and want some guidance through the troubleshooting process feel free to send us an email at: [email protected] Expert: spaman101 replied4 years ago. The impeller is spinning in the pump, flow into the tub seems to be pretty low. If that doesn't work then turn it back to its original position, so counter-clockwise, back to its original position and then keep on turning it counter-clockwise up to one turn to

Check for excessive filter duration. Transcript The interactive transcript could not be loaded. Check water level in spa. Generated Tue, 18 Oct 2016 03:27:31 GMT by s_wx1131 (squid/3.5.20)

There's got to be something wrong with this pressure switch".

© Copyright 2017 renderq.net. All rights reserved.