Loading...
Home > Error Code > Hyosung Error Code 20003

Hyosung Error Code 20003

Contents

It was detected that the feed lever was open before ther receipt printer started to operate.) How to fix the problem: 1. Install after rearranging notes in cassette 4004A00Error of note jam (Separated rejection)_ Remove jammed notes on CDU return path _ Remove dust in CS1~CS4 sensor _ Install after rearranging notes in Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). C00FF Sensor blocked N/A CANCE User canceled transaction at surcharge This is not an error, but rather a statistic to notify how many users respond "no" to the surcharge notification. have a peek at this web-site

Contact host processor D00A8 FS omitted (after surcharge amount in configuration message) Verify all programming. Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). Check that the denomination in Transaction setup matches the actual denomination loaded C0042 Note jam Check for notes in the Cash Dispenser. Specific meaning or definition can vary between the different processors.

Hyosung Atm Error Codes

D0050 Transaction is not approved Code reported by host processor (Shazam). Check if CS7/17/27(NS11/16) is fully pressed while the cassette is loaded. 3. D0053 No savings account Code reported by host processor. Code reported by host processor (Shazam).

C001x CDU sensor is tripped Most typically a COO11 error, this would indicate a bill jam at the exit sensor of the Cash Dispenser. Remove a jammed note in 4 Cassette.2. Check if the CS3 sensor cable is disconnected4. Hyosung Epp Error Reboot ATM 2.

Exchange a sensor after abnormal operating the CS14 sensor . 400A7When cam doesnÕt arrive at dispense position within regulated time (cam error) 400A8When cam doesnÕt arrive at delivery position within regulated Exchange sensor after abnormal operating CS13 Sensor 4004600Program error(Separated rejection)1. Check if each sensor is mounted. 2. http://www.accessatm.com/service/atm-error-codes/hyosung-error-codes/ D1706 Modem connection error Phone line connected to ATM will not support data communication.

Clean CS31AB and CS41AB, or remove foreign objects. 2. Atm Error Code 3-da001 Replace hard disk drive 9719400Invalid Cash Unit ID1. Contact host processor D00A5 FS omitted (after total cash dispense amount in day close) Verify all programming. Specific meaning or definition can vary between the different processors.

Hyosung Error Code 97999

C0053 CDU double detect module failure. Remove note from the CDU delivery path. 2. Hyosung Atm Error Codes D0041 No credit account found for the CCN Code reported by host processor (Shazam). Nautilus Hyosung Error Codes Remove the remaining notes at a sensor in front of the CST2.

Reboot ATM 2. Check This Out Contact host processor D00A5 FS omitted (after total cash dispense amount in day close) Verify that version of Mini-Bank Software matches host processor. Call your attendant 9722068Invalid Media Name1. Check all wiring to mainboard. Hyosung Error Code 97999(04)

If the sensor is not being pressed then the error will occur. Open the reject/retract box cover 2. Check the CDU received command2. Source Clean CS2, CS4A and CS4B 4001DCS2, CS4A and CS4B Dark detection during initializing or dispense reserved operationThe same as #40011, #40014 and #40018 error handling 4001D00Detecting CS2, CS4A, CS4B Dark 4001ECS3,

Remove a dust or foreign objects on the CS13 sensor4. Hyosung 2700 Error Codes Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Call your attendant 9722100Field Error (This Field must have initial value)1.

D0014 Invalid Card Number Code reported by host processor.

Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Remove the remaining notes and foreign objects at the position of the CS41AB sensor 2. Initialize Cash Dispenser (CDU) 2. Hyosung 1800 Error Codes Change Main Motor Encoder Slit Sensor CS8 4003100Failed in checking the reject gate solenoid echo 4003200Failed in checking the present gate solenoid echo 4003300Check sum error (No information is set)1.

If they are broken the cassette will not stay in the dispenser. 20002 Low Cash Low cash warning sensor on dispenser is open. Check notesÕ status in the reject box 2. Close the lever of print head completely 20102Receipt printer head overheated1. http://renderq.net/error-code/ibm-db2-error-code-204.php If this error is consistent, the printer or mainboard may require service.

Remove dust in CS1A, CS1B Sensor5. Call your attendant 9799905SENSOR CHECK1. Check if the CIU power cable is connected. 90001Card Swipe Error.This error shows the number of times a customer swipes their cards unsuccessful. 97120Unable to create INI file 97121Unable to read Check second Dip Switch in Cash Dispenser B/D3.

If you wish to change this warning, please update your preferences through our website. Check if the CS31B and CS31B sensor cables are disconnected4. If error occurs after checking CS 15 disconnection and operation, replace a sensor. 400C800Something is detected on CS2 sensor after dispense operation 400C800Something is detected on CS14 sensor during dispensing bills Exchange Sensor after abnormal operating CS7 Sensor 4003ECS21B DARK Detected (Initial recovery, Separated reject)1.

Reboot ATM2. Contact host processor D00A0 FS omitted (after account balance) Verify all programming. ADNxx Printer connection error Check cables between Printer and Mainboard, remove cables (even though they may be attached) and re-connect. Replenish receipt paper in paper charger2.

Change CS5_1 Sensor 4003600Error of CS 2, CS13 sensor during initialization 4003700Error of 2 sheets detecting sensor(CS5_1/CS5_2) for dispensing1. C00E0 NS2A, NS2B dark Nanocash only - verify connections to sensors. Check the status of Black mark sensor 2. This error is of concern only if it is repeated.

© Copyright 2017 renderq.net. All rights reserved.