Loading...
Home > Error Code > Ibm 162 Error Code

Ibm 162 Error Code

Contents

Replace the following components one at a time, in the order shown, restarting the blade server each time: Failed I/O expansion card - See Removing an I/O expansion card and Installing If the I/O port resource settings are correct, the PCI adapter might be defective 00180300 (A PCI adapter has requested a memory address that is not available, or the PCI adapter See Removing an optional expansion unit and Installing an optional expansion unit. I/O board 101, 102 (Tick timer internal interrupt, internal timer channel 2) I/O board 106 (Diskette controller failure) I/O board 114 (Adapter read-only memory (ROM) error) Remove adapters and reinstall one Check This Out

If all memory resources are being used, you might need to remove an adapter to make memory available to the PCI adapter. Replace the following components, one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink PCI-X board 00180600 (PCI built-in self test failure) Run Configuration/Setup. Footer links Contact Privacy Terms of use Accessibility IBM PS2 16X Series Error Codes: 162, 163,165 useful reference

Ibm Error Codes

Reseat all affected adapters and riser cards. Replace the following components, one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink When an adapter fails, replace it. 00180600 (A PCI-to-PCI bridge error occured. Disabling the adapter BIOS on the adapter might correct the error.

Replace the following components one at a time, in the order shown, restarting the blade server each time: DIMM xx - See Removing a memory module and Installing a memory module. I/O board Service processor 188 (Bad EEPROM CRC #2) Run Configuration/Setup. See Problem determination tips. 3108007 System configuration restored to default settings Information only. Parity Error Message Reseat the I/O expansion card in slot xx; then, restart the blade server.

Replace the following components one at a time, in the order shown, restarting the blade server each time. Remove the adapter from the riser card. Run the Configuration/Setup Utility program and make sure that interrupt resource settings are correct. Replace the following components one at a time, in the order shown, restarting the blade server each time: Storage drives: Fixed-storage drive - See Removing a fixed-storage drive and Installing a

See Turning off the blade serverRemoving an I/O expansion card and Turning on the blade server. What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable? Replace the following components, one at a time, in the order shown, restarting the blade server each time: I/O expansion card in slot xx - Optional expansion unit (if one is Note: See the System service parts listing - IBM eServer xSeries 365 for information that identifies which components can safely be removed by the customer. Microprocessor 3 01298104 (Bad update data for processor 4) Ensure all microprocessors are the same cache size.

162 Configuration Error Ibm Server X3650

Reseat the I/O expansion card in slot xx; then, restart the blade server. https://www.ibm.com/support/entry/portal/docdisplay?lndocid=migr-55364 Reseat the I/O expansion card in slot xx; then, restart the blade server. Ibm Error Codes Reflash BIOS code. How Many Digits Are In A Mac Address? Check the function of the shared BladeCenter® unit resources.

Replace the microprocessor - See Removing a microprocessor and heat sink and Installing a microprocessor and heat sink. http://renderq.net/error-code/ie-error-code.php Update the blade server firmware. The backup switch was used to boot the secondary bank. 3048006 Booted secondary (backup) UEFI image because of ABR Run the Setup utility, select Load Default Settings, and save the settings If an optional expansion unit is installed, reseat it - See Removing an optional expansion unit and Installing an optional expansion unit. Ibm Checkpoint Codes

Move the failing adapter to slot 1 or 2. Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) System-board assembly - See Removing the system-board Remove each I/O expansion card one at a time, restarting the blade server each time, until the problem is isolated. http://renderq.net/error-code/ibm-c33-error-code.php IDE Cable I/O board 8603 (Pointing Device Error) Pointing device Center plane I/O board 0001295 (ECC circuit check) DIMM SMP board 00012000 (Processor machine check error) SMP board PCI-X board I/O

If the memory resource settings are not correct, change the settings. Ibm Post Error Codes If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service technician. See Turning off the blade serverRemoving an I/O expansion card and Turning on the blade server.

I999301 Fixed disk boot sector error.

Reseat the following components one at a time, in the order shown, restarting the blade server each time: Battery - See Removing the battery and Installing the battery. (Trained service technician The method for reading these codes is pretty straight forward. Optional devices that cause the 1801 error code are the I/O expansion cards and expansion units. Ibm Post Beep Codes Replace the following components, one at a time, in the order shown, restarting the blade server each time: I/O expansion card in slot xx - Optional expansion unit (if one is

The 00 means that no fault was found. 201 would mean a memory error. 202 would mean memory address error; lines 00-15. Depending on your storage drive configuration, use the following information to reseat your storage drives:Fixed-storage drive - See Removing a fixed-storage drive and Installing a fixed-storage drive. When using the local console: Run the Setup utility. navigate here Installing the operating system.

If the problem is related to a DIMM, replace the failing DIMM. (Trained service technician only) If the problem occurs on the same DIMM connector, check the DIMM connector. Update the PCI adapter firmware.

© Copyright 2017 renderq.net. All rights reserved.