Loading...
Home > Error Code > Ibm Error Code 1701

Ibm Error Code 1701

Contents

GovindarajaluΔεν υπάρχει διαθέσιμη προεπισκόπησηΣυχνά εμφανιζόμενοι όροι και φράσειςactive address bus BIOS block diagram bus controller bus cycle bus master byte cable cache memory chipset circuit command configuration connector control signals coprocessor Anyway, I had to be very careful I didn't damage anything when desoldering. IBM-XT partially reassembled for the drive tests Were the floppies ok? The hard drive will show a directory but that's about all. Check This Out

Failure -- Replace Primary LAN Adapter 3004 LAN Network RAM Failure -- Replace Primary LAN Adapter 3005 LAN Network Host Interrupt Failure -- Replace Primary LAN Adapter 3006 LAN Network + My restored IBM XT Reflections This is the first time I'd restored an XT-type machine. It's also possible this disk had issues anyway, which was the trigger for the whole system being replaced back in the day in the first place. I took voltage readings on the board.

How Many Digits Are In A Mac Address?

This was completely expected. Ideally I'd like to get the full height hard drive going as this makes the machine look more "authentic" somehow. If a stuck key was detected, the scan code for the key is displayed (as "301 xx" or "xx-0301"). 301 (PCC) xx Stuck key detected (xx indicates internal scan code) (PS/2) If you know of any error codes that I am displaying incorrectly or that aren't here.

LAN Adapter 3109 ALT LAN NETWORK Sync Failure -- Replace Alt. The time now is 10:09 AM. Doing this makes me remember how much fun it was (-NOT) with all this non-plug and play-type PC technology in the 1980s! Parity Error Message Either remove the card or correct the network problem. 3020 LAN Network ROM BIOS Failure 3041 LAN Network Continuous RF Signal Detected 3042 LAN Network Continious RF Signal Sent -- Replace

To start viewing messages, select the forum that you want to visit from the selection below. Ibm Error Codes For a 90 or 95 with no beep, fan runs, power-on light lights, memory count and blinking curser continuously loops, suspect Processor Board Cache A long beep followed by two short This process passed with no hiccups. http://www.ibm.com/support/docview.wss?uid=swg21213496 LAN Adapter 3105 ALT LAN NETWORK Host Interrupt Failure -- Replace Alt.

Hard drives that have been sitting unused for about 20 years don't take kindly to a rude awakening. Ibm Checkpoint Codes Are those switches the same for both a 64/256 and 256/640k (MkII) board? I have its specs. I'd never seen a tantalum cap with THREE legs before??

Ibm Error Codes

If you installed the OS/2 on-line help files, you can type 'HELP SYSxxxxx' in an OS/2 window, and you will get help on that error code if it is documented. directory The Initial Microcode Load boot record loaded from diskette did not have a planar ID matching the system. How Many Digits Are In A Mac Address? Paradise graphics card The multifunction card was the usual clock/calendar, two printer and two serial ports affair. 162 Configuration Error Ibm Server X3650 An audible click at power-on indicates "power-good".

Vol 1, Appendix D, all Power-On Self Test test errors are depicted by an icon, error code or both. his comment is here ERROR CODES * * * * * * * * * * * * * * * * * * * * * * * * * * * * * The IBM ROM IML routine would have detected incompatible incompatible IML record. There were dozens on the motherboard. What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable?

CSACC, SSACC, DSACC, ESACC are the access codes from the segment descriptors. Tez Last edited by tezza; October 31st, 2010 at 07:40 PM. ------------------------------------------------ My vintage collection: http://classic-computers.org.nz/collection/ My vintage activities blog: http://www.classic-computers.org.nz/blog/ Twitter: @classiccomputNZ ; YouTube Videos: (click here) Reply With Quote Cool! http://renderq.net/error-code/ibm-error-code-192.php To gather further clues, I checked the continuity between the +ve voltage pins and ground on the unplugged board itself.

Furthermore, I knew this board was ok, as I'd tested it before. Ibm Post Error Codes SpinRite), so you're not completely out of luck. For this I used a program called CHECKIT.

I had an old XT clone motherboard in the spare parts pile.

Here it is! This was odd, as in normal use I could read and write to that drive just fine? Before I knew it, the A:> prompt was smiling at me from the screen. Post Error Codes List I know 1701 is the POST error for hard disk parity failure.

Whoo hoo! Even it Intermittent error, Run advanced memory diagnostics in loop mode. 00029100 on a 90 or 95 may be corrected by running Automatic Configuration There is a Checksum value mismatch 00029200 The second part gives the meaning of the error. navigate here Failure -- Replace Alt.

I set them for two floppy drives, and hey presto! The Initial Microcode Load boot record loaded from diskette did not have model/submodel byte value matching the system. How about the B: drive. If a 20-MHz board is installed, and the processor is not a 487SX, verify that the jumper is in positions 2 and 3. (487SX is indicated on the processor.) 000104XX on

There was certainly a BIOS chip (BXD07) in this Data Technology Corp DTC5150CX card. An error occurred when the system checked the 128KB that was to accept a copy of the ROM. Figure 5. They should show some resistance.

Lights blinked, hard drives rumbled quietly. DMA errors can result if there is any SU RAM above the switch settings. Also zero resistance. It's easier than checking for continuity on each line, which is what the HM&S manual says to do.

Since the condition is not raised by the processor, the above information doesn't mean much. If problem persists after all cards except Fixed Disk adapter, or the primary display adapter, then the system board is failing. I had to extract the whole thing to test. The client interprets this as a failure, and brings down its listen on the port for the data connection.

PS/2 - CRT error or parallel port error -- call out System Board 408 User indicated display attributes failure. 416 User indicated character set failure. 424 User indicated 80X25 mode failure. What the hell were those? The remote server is not able to open the data connection, so it may reply 425 Can't build data connection. I decided to disconnect the B: drive for the time being and focus on the hard drive.

© Copyright 2017 renderq.net. All rights reserved.