Loading...
Home > Error Codes > Hydro Quip Error Codes

Hydro Quip Error Codes

Contents

Please try the request again. FLO = Flow Switch (heater is deactivated. Touch any button to reset the system. Support: Balboa topside displaying (SnA or Sa) 51. http://renderq.net/error-codes/ibm-error-codes.php

Support: Wiring information for the (15-350-2130) 48-Frame 1.5HP 110V CD Waterway Pump, 342061A-15 104. All electrical and plumbing parts we sell are intended for installation by a licensed electrician or licensed contractor. HL = High limit switch tripped. Why does the motor run in high speed in circulation and heating mode? 36. https://spacare.com/spasideerrorcodes.aspx

Hot Tub Error Codes

Support: Why does the spa motor over heat or suddenly turn itself off? 40. Can I buy just the logic chip for a circuit board? 132. HOT = Circuit Board temperature has exceeded acceptable limit. Do not enter the water.

Pump may also be deactivated). Support: New pump making vibrating or buzzing noises on low and/or high speed, but runs fine. 87. Before Purchase Questions131. Vita Spa Error Codes ICE Freeze condition, pump and heater activate at 55 degrees.

Generated Tue, 18 Oct 2016 03:24:24 GMT by s_wx1127 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection What is the minimum and maximum temperature setting for the VS-Series Spa Controllers? 108. The Spa or Hot Tub Panel Displays: HH, OOH, OH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights At least one of the sensors has detected water temperatures of http://www.spaspecialist.com/vistasilverpanel.html No action is necessary.

This is a normal spa function; no further action is necessary.When either sensor reads below 40 degrees F., the system provides freeze protection. Hydroquip Spa Systems How do I remove/install SpaGuts heater element? 33. The Heater On Light Indicator will blink on the function panel whenever there is a call for heat and the heater has not yet been powered. The second press will change the pump to high speed.

Balboa Hot Tub Error Codes

Support: Wiring information for the (15-350-2110) 48-Frame 1.0HP 110V SD WaterWay pump, 342041A-10 99. http://www.spapartsshop.com/spasideandtopsideerrorcodes.aspx If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected. Hot Tub Error Codes Support: Rotating the pump discharge on a Vico Pump that has a locking plate. 79. Hydroquip Spa Troubleshooting Pressing it again will return it to the filter or heat mode with the low speed running.

The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue. Check This Out If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open Support: Balboa Controller VS500Z and VS501Z Mode Settings for Standard, Economy and Sleep. 63. ACC (Applied Computer Controls)Systems for Spas or Hot Tubs: CoLd = Temperature in the spa heater housing is below 40° F. Hydroquip Hq6000

SEoP = Sensor open or disconnected. Fill out my Wufoo form! The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. http://renderq.net/error-codes/ibm-sql-error-codes-db2.php Support: GFCI breaker is now tripping off a Spa Circuit Board. 103.

Is Ozone safe for soft tubs? 143. Marquis Spa Error Codes Support: On an initial installation of a motor why does the motor run momentarily then stop? 42. Support: New spa heater is installed, and it will not heat (no heat) 105.

Support: SpaGuts Inline Bath Heater Installation 114.

Support: Air siwtch is sticking or not working on Pneumatic Controller. 24. Support: The Glued Plumbing Configuration will not align up to the Pump and Heater on a Spa Pack. 68. NOTE: You may not be able to turn the pump off if it has started an internal heat or filtration cycle. Gecko Spa Pack Error Codes Support: Smoke coming from inside a Balboa or SpaGuts VS Series Spa Controller. 74.

Heater is deactivated.F2 = 4 hours daily filtrationF4 = 8 hours daily filtrationF6 = 12 hours daily filtrationFC = continuous filtration EasyPak Control Systems for Spas or Hot Tubs: C = It is recommended that the system is powered up at a time when the programmed cycles do not interfere with sleeping hours. If you see water flowing normally on low speed, and the water level is correct, then remove the filter(s) to see if the error code goes away. have a peek here Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when

Filter Cycle has stopped & "Filter" indicator is Flashing not an error but a feature: either the filter cycle is in a 40min minute time-out to avoid ozonater activation while spa Will a heater that is rated for 110V (120V) work on 220V (240V)? 142. dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). The system returned: (22) Invalid argument The remote host or network may be down.

Power on the spa must be cycled before the heater will function again. thunderstorms, voltage surges, etc.). Inverted Display ~ Press Filter key for 5 seconds (certain Models) Pump Starts randomly for 1 Minute & Filter indicator Flashing ~ Smart Winter Mode nor and error but a feature PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected.

Support: Dashes displaying on the topside panel for a SD6600-720 LX-15 Sundance Board 94. Support: The VS Series Control System is coming on too much, and may not be normal. 126. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF.

Support: The power terminal block on the circuit board is burnt (CS6200 Series). 47. The low speed pump or circ. FL1 / 03 Pressure switch not closing when pump is running and heater is trying to heat. Flashing dots & Lit light on display ~ Hi-limit trip, reset power to clear.

Support: I ordered the wrong plumbing configuration on the spa pack. 17. Support: Functions of an air venturi valve or a water diverter valve. 138. The system returned: (22) Invalid argument The remote host or network may be down. at heater.OHS = Overheat.

© Copyright 2017 renderq.net. All rights reserved.