Visit the following links: Site Howto | Site FAQ | Sitemap | Register Now If you have any problems with the registration process or your account login, please contact us. Select "PIO Only" and then click the "OK" button. If the device has a red "X" on the icon next to its description, the hardware is disabled; proceed to Step 4 to enable it. Whenever I try to do a dd or md5sum on a CD (particularly the Slackware 10 set I bought from edmunds-enterprises.com) it'll get most of the way through and then stop
Unfortunately, it ends up with the message "Cannot continue the hardware update wizard. And still, at times, I can just play the CD as if nothing is the matter. The wizard could not find a better match for your hardware than the software you currently have installed". It's dd with smarter error handling.
Running Windows 7 Home Premium. Someone on this forum suggested it was a bad disk. If an error is shown, proceed to Step 5. # Step 5 Go to the General tab and click "Troubleshoot" found under the Device Status section then press "OK." Follow the Otherwise, go to Step 5. # Step 4 Go to the General tab and click "Enable Device" found under the Device Status section; then press "OK." (Note: You may have to
Next attempt: dd_rescue. Become part of our maker community. Want to know which application is best for the job? If this solution fixed the I/O error, you are finished.
I just redo dd until it goes of without a hitch. I/o Device Error Windows 8 If above solutions resolved the issue, you are finished. Last edited by JZL240I-U; 09-28-2004 at 06:32 AM. http://www.ehow.com/how_6107630_fix-cd_rom-i_o-device-errors.html You can fix this problem by changing to the correct transfer mode.
jimdaworm View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by jimdaworm 09-12-2004, 12:13 PM #8 Ebel Member Registered: May 2004 Distribution: Slackware Remove the floppy diskette or CD from the computer and put it back in and press any key to continue. Ubuntu Logo, Ubuntu and Canonical © Canonical Ltd. I have been trying to make cd images with dd as k3b says that verson 2.0.3 of cdrecord doesn´t support cd cloning.
I think I have tried all three drives though. http://serverfault.com/questions/48794/cannot-mount-cdrom-in-linux-due-to-i-o-error Test the drive. I/o Device Error Windows 7 Can't find your answer ? I/o Device Error Windows 10 jimdaworm View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by jimdaworm 09-28-2004, 07:49 AM #14 JZL240I-U Senior Member Registered: Apr 2003 Location:
At any rate, one drive would always screw up with rawread(I/O errors) and one drive was fine. The following happens on an Intel i7 system, running an up-to-date Ubuntu Karmic, Desktop Edition, 64-bits. vBulletin ©2000 - 2016, Jelsoft Enterprises Ltd. This can be caused by a bad disc or when the transfer mode, used by the operating system, is not supported by the CD-ROM drive or has been changed. The Request Could Not Be Performed Because Of An I/o Device Error
asked 7 years ago viewed 1396 times active 7 years ago Blog Stack Overflow Podcast #91 - Can You Stump Nick Craver? Digital Photo Recovery Solutions and Software Best Ways to Fix Windows System32 Error How to Run CHKDSK or Checkdisk? If a clean boot fixes the problem, there may an incompatible program or driver on your PC.
Slackware 10 d1 and d2 and arch linux 0.6 (All were orignally cd imges downloaded form the net) dd gets to right near the end of the cds and then says: Is this likely? Then, click OK and exit all windows. Solution 3: Change the transfer mode for the drive in IDE Channel Properties If the transfer mode for the drive was changed or is incorrect, Windows cannot transfer data from the
Select Manage from the resulting menu 4. dd made images of these cds without any errors. Both CD & DVD. –LapTop006 Aug 2 '09 at 11:42 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign up Submit Your Work!
A subset will open, listing the different IDE ATA/ATAPI channels for the computer. Fixed by changing the SATA port on the motherboard the original Drive was connected to.