Loading...
Home > I O Error > I/o Error Abend B37-04

I/o Error Abend B37-04

Contents

S0E0 - 1D - A SQUARE ROOT EXECEPTION OCCURED. S013 - 60 - AN OPEN MACRO WAS ISSUED FOR A DATASET WITH A DCB SPECIFYING RECFM=F, AND BLKSIZE WAS NOT EQUAL TO LRECL. S0C4 - PROTECTION EXCEPTION - A VIRTUAL ADDRESS COULD NOT BE TRANSLATED INTO A REAL ADDRESS.POSSIBLE CAUSE- ENTRY NOT FOUND- INVALID ADDRESS WAS REFERENCED DUE TO SUBSCRIPT ERROR OR BAD PARMS- ASK THE OPERATOR TO REPLY ‘U' OR SPECIFY ANOTHER VOLUME SERIAL.

E37 Primary and secondary space filled - Lack of disk resources. S004 - 05 - INVALID FORMAT CARD OR AN INVALID DEVICE SPECIFIED WITH OPTICAL MARK READ (OMR). S0F8 - 10 - THE SVC ISSUER WAS IN CROSS MEMORY MODE. We're matching your request. http://www.ibm.com/support/docview.wss?uid=swg21227089

Iec030i B37-04

S0E0 - 2B - AN ACCESS LIST ENTRY SPECIFIED AN INVALID DATA SPACE. S118 - 02 - OUTPUT AREA (ADDRESS IN GPR 0) WAS NOT IN CALLER'S REGION. Reboot your workstation. -+Z_586 Message = received data failure. S171 - 16 - THE INPUT VSL OR ECB FAILED TO PASS THE PAGE SERVICES INTERFACE VALIDITY CHECK.

S113 - 0C - AN OPEN TYPE=J WAS ISSUED, BUT NO JFCB EXIT WAS FOUND IN THE DCB EXIT LIST. The following are the most commonly found system abend codes. S305 - 18 - PRIVATE AREA SUBPOOL NOT FOUND. Iec028i 837-08 S16E - 14 - AM VALUE DOES NOT EQUAL DEBAMTYP VALUE.

In the job control cards SMDSPACE=NO is specified. S301 - AN ECB SPECIFIED IN A WAIT MACRO ALREADY HAD ITS WAIT FLAG ON. All Fields Required First Name Last Name Email Address How can we help you? http://ibmmainframes.com/about51994.html The abend code SD37 is raised when you don't specify a secondary allocation.

S002 - 34 - A READ MACRO WAS ISSUED FOR AN OUTPUT-ONLY DASD DATA SET. Iec070i 209-220 Attention should be given to the publication "RACF, A Component of the IBM Operating System of The University of Georgia." This is a brief general information manual published specifically for IBM THE DATASET HAS AN INDEXED SEQUENTIAL ORGANIZATION. RECOMPILE AND RERUN.

System Abend Code = B37, Reason Code = 00000004

THE FAILING DCB IS NOT OPENED, HOWEVER THE TASK IS NOT TERMINATED. http://forums.informationbuilders.com/eve/forums/a/tpc/f/7971057331/m/3781086603 S013 - 5C - AN OPEN MACRO WAS ISSUED FOR A SEQUENTIAL DATASET USING THE QUEUED ACCESS TECHNIQUE. Iec030i B37-04 S013 - 7C - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER READER DATASET, BUT THE LRECL PARAMETER IN THE DCB WAS ZERO. E37-04 The actual jobname, procedure name, and stepname for your job will appear in the indicated locations in the message.

S11A - A PROTECTION CHECK OCCURRED WHEN THE SYSTEM TRIED TO STORE INTO A USER SUPPLIED OS/VS CAMLST WORK AREA. ERROR ID: none 2. If the error reoccurs, consult your technical support staff IEC015I A34-04 An attempt was made to read an unopened file. S0F8 - 1C - THE SVC ISSUER WAS NOT AUTHORIZED FOR SVC MICROCODE ASSIST. Ifg0554a

TWO ENQ MACROS WERE ISSUED FOR THE SAME RESOURCE IN THE SAME TASKWITHOUT AN INTERVENING DEQ MACRO. S0F8 - 0C - THE SVC ISSUER WAS DISABLED. S213 - 68 - AN OPEN FOR A PDSE WAS ISSUED WITH RECFM=FB AND LRECL=0. THE RECORD LENGTH IS GREATER THAN THE BLOCKSIZE SPECIFIED IN THE DCB.

S002 - 50 - SERIALIZATION OF AN INTERNAL SAM CONTROL BLOCK (SACB) USED FOPR PROCESSING HAS BEEN VIOLATED. B37 Error Many times the appropriate manuals are not readily available for the user's access. Readers based in India, can buy the e-book for Rs. 50 only or the print book.

U2052 - INCREASE REGION SIZE, NOT ENOUGH CORE.

S16E - 20 - DEB TABLE CONTAINS 32760 BYTES AND TYPE = ADD. ERROR ID: IEF301I 2. NOT ENOUGH REAL STORAGE AVAILABLE TO BACK A MINIMUM NUMBER OF VSM CELLS (IN LSQA) DURING LOCAL CELL POOL EXPANSION. Iec032i PLEASE REPORT THIS PROBLEM TO THE SYSTEMS GROUP.

IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S137 OPERAND FOR MORE SPECIFIC INFORMATION: H ABEND O(S137-RC) S137 - 04 - AN I/O ERROR OCCURRED WHILE WRITING IN THE ABNORMAL TERMINATION DUMP, THE TCB FIELD TCBEXCPD (AT OFFSET C0) POINTS TO THE EXCP PROBLEM DETERMINATION AREA. DESCRIPTION: This error occurred during execution of a LINK or LOAD instruction. CORRECTIVE PROCEDURE: Assuming that the program is correct, increase the appropriate specification by use of a MAIN card.

Check your CONFIG.SYSFILE -+Z_590 The connection with the controller has been dropped. S024 - AN ABNORMAL TERMINATION OCCURRED IN PRINT SERVICES FACILITY. S202 - 08 - FOR A POST IN A USER KEY AND A WAIT IN A SYSTEM KEY, THE ECB TO BE POSTED DOES NOT MATCH ANY ECB BEING WAITED ON.

© Copyright 2017 renderq.net. All rights reserved.